Getting Started - A Basic Toolbox: Part 2

A post from my earlier blog, The Handy Dandy Man.

Screwdrivers. Yes, that's right, plural. At the very least you will need two: a slotted screwdriver and a #2 Phillips-head screwdriver. I have over a dozen screwdrivers and could use more. At the very least, you should have the ones I've recommended here. I commonly use:

• 4" x 3/16" slotted driver (recommended)
• 4" x 1/4" slotted driver(recommended)
• Stubby 3/16" slotted driver
• 2" 3/32 slotted driver
• 4" #2 Phillips-head driver (recommended)
• 4" #1 Phillips-head driver (recommended)
• Stubby #2 Phillips-head driver
• 2" #0 Phillips-head driver
• A set of 6 jewelers screwdrivers: 4 slotted; 2 Phillips-head

Cordless Drill/Screwdriver. You will most likely use this tool more than you can imagine. If not, you're probably not using it for everything you could.

Get a good one. I have two. Thanks to my brother, I now own a Makita 18v Lithium-Ion 1/2" Driver Drill (BDF452HW). I'd be lost without this tool- the most-often used tool in my collection.

O.K., Here we go. Part 2 of putting together the basic toolbox.

Don't settle for less than professional on this tool. I recommend Makita, DeWalt, Milwaukee, Bosch, or Rigid. Tools by Black & Decker, Ryobi, or Skil tend to be more affordable, but lack the same power and durability of the names I mentioned earlier.

Remember, if you buy an inexpensive tool designed for the homeowner who will use it only occassionaly, it may not last as long or perform as well as a more expensive tool designed for the professional. You may end up spending your money twice. Spend your money right the first time and buy a better tool. Trust me, you won't regret this decision.

For quick small jobs, I also own a small, inexpensive, 3-position, electric screwdriver (Black & Decker Model 9078).

Set of Drillbits and Drivers. Get a small set of drill bits- usually 1/16" through 3/8" is enough, but if you can, get a set that has a 1/2" with a 3/8" shaft. You may also want to consider a set of paddle bits for doing larger holes, up to 1" or more.

In regards to drivers, I have a "Speed-Lok" set of drivers and bits that allows me to quickly change between drill bits and screwdriver bits (Craftsman Model #26144).

Slip-joint or "alligator" pliers. These are essential for holding and gripping...whatever. They're ideal for tightening or loosening various sizes of nuts or other threaded connectors. They can also be used to grip and remove things, such as pulling out small nails, tacks, or staples. They are truly a multi-purpose tool that is essential to any toolbox.

Needle-nose pliers are essential for doing electrical work (bending wires to fit around the switch or duplex screws) and for getting into any tight space where you need to grip something. Some come with side cutters which are very convenient to have if doing a lot of wiring.

Tongue-and-groove pliers. Often called "Channellocks" after a popular manufacturer of the tool, these are great for doing plumbing work as they can often open wide enough to fit around 1-1/4" or 1-1/2" drain pipes. Again, though, this tool has many uses.

Adjustable Wrench. If you ever intend to turn nuts or similarly-shaped items (e.g. water and gas connectors), you gotta have at least one of these. I have a set of 4 - different sizes for different jobs. It's often difficult to get into a tight space with a large adjustable wrench, and smaller ones don't open wide enough to accomodate larger turning surfaces. I recommend at least two- a larger one and a smaller one.

Diagonal Cutters. Not just for electrical work, these can also be used to cut through small brads, nails, staples, etc. You will find ways to use these. They are ideal for pulling staples out after removing flooring or carpet.

Vise-Grips or locking pliers. If you need to hold something and wish you had that third hand- that's what locking pliers are for. While I don't use these often, a small set (usually 2 or three) will cover jsut about all of your needs.

Allen or hex wrench set. Seems you can't buy anything today that doesn't utilize an Allen or hex screw, especially ready-to-assemble furniture. A small set isn't all that expensive and you'll be glad you have them when the need arises. Here's a tip: Buy a set that is both SAE (Standard American Equivalent) and metric. Many of the RTA furniture makers are Asian or European and they tend to use metric fasteners.

Set of combination wrenches. There are times when having a closed or box wrench is just necessary. Where a plier or adjustable wrench is just too cumbersome or keeps slipping off the nut or hex bolt, nothing is better than a box wrench. An adequate set is about $25-$35.

Stay tuned for Part 3, Knives, Saws, Tapes, etc.